549 lines
17 KiB
Systemverilog
549 lines
17 KiB
Systemverilog
// SPDX-License-Identifier: Apache-2.0
|
|
// Copyright 2019 Western Digital Corporation or its affiliates.
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
//
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
// all flops call the rvdff flop
|
|
|
|
|
|
module rvdff #( parameter WIDTH=1 )
|
|
(
|
|
input logic [WIDTH-1:0] din,
|
|
input logic clk,
|
|
input logic rst_l,
|
|
|
|
output logic [WIDTH-1:0] dout
|
|
);
|
|
|
|
`ifdef CLOCKGATE
|
|
always @(posedge tb_top.clk) begin
|
|
#0 $strobe("CG: %0t %m din %x dout %x clk %b width %d",$time,din,dout,clk,WIDTH);
|
|
end
|
|
`endif
|
|
|
|
always_ff @(posedge clk or negedge rst_l) begin
|
|
if (rst_l == 0)
|
|
dout[WIDTH-1:0] <= 0;
|
|
else
|
|
dout[WIDTH-1:0] <= din[WIDTH-1:0];
|
|
end
|
|
|
|
|
|
endmodule
|
|
|
|
// rvdff with 2:1 input mux to flop din iff sel==1
|
|
module rvdffs #( parameter WIDTH=1 )
|
|
(
|
|
input logic [WIDTH-1:0] din,
|
|
input logic en,
|
|
input logic clk,
|
|
input logic rst_l,
|
|
output logic [WIDTH-1:0] dout
|
|
);
|
|
|
|
rvdff #(WIDTH) dffs (.din((en) ? din[WIDTH-1:0] : dout[WIDTH-1:0]), .*);
|
|
|
|
endmodule
|
|
|
|
// rvdff with en and clear
|
|
module rvdffsc #( parameter WIDTH=1 )
|
|
(
|
|
input logic [WIDTH-1:0] din,
|
|
input logic en,
|
|
input logic clear,
|
|
input logic clk,
|
|
input logic rst_l,
|
|
output logic [WIDTH-1:0] dout
|
|
);
|
|
|
|
logic [WIDTH-1:0] din_new;
|
|
assign din_new = {WIDTH{~clear}} & (en ? din[WIDTH-1:0] : dout[WIDTH-1:0]);
|
|
rvdff #(WIDTH) dffsc (.din(din_new[WIDTH-1:0]), .*);
|
|
|
|
endmodule
|
|
|
|
// versions with clock enables .clken to assist in RV_FPGA_OPTIMIZE
|
|
module rvdff_fpga #( parameter WIDTH=1 )
|
|
(
|
|
input logic [WIDTH-1:0] din,
|
|
input logic clk,
|
|
input logic clken,
|
|
input logic rawclk,
|
|
input logic rst_l,
|
|
input logic scan_mode,
|
|
|
|
output logic [WIDTH-1:0] dout
|
|
);
|
|
|
|
`ifdef RV_FPGA_OPTIMIZE
|
|
rvdffs #(WIDTH) dffs (.clk(rawclk), .en(clken), .*);
|
|
`else
|
|
rvdff #(WIDTH) dff (.*);
|
|
`endif
|
|
|
|
|
|
|
|
endmodule
|
|
|
|
// rvdff with 2:1 input mux to flop din iff sel==1
|
|
module rvdffs_fpga #( parameter WIDTH=1 )
|
|
(
|
|
input logic [WIDTH-1:0] din,
|
|
input logic en,
|
|
input logic clk,
|
|
input logic clken,
|
|
input logic rawclk,
|
|
input logic rst_l,
|
|
input logic scan_mode,
|
|
output logic [WIDTH-1:0] dout
|
|
);
|
|
|
|
`ifdef RV_FPGA_OPTIMIZE
|
|
rvdffs #(WIDTH) dffs (.clk(rawclk), .en(clken & en), .*);
|
|
`else
|
|
rvdffs #(WIDTH) dffs (.*);
|
|
`endif
|
|
|
|
endmodule
|
|
|
|
// rvdff with en and clear
|
|
module rvdffsc_fpga #( parameter WIDTH=1 )
|
|
(
|
|
input logic [WIDTH-1:0] din,
|
|
input logic en,
|
|
input logic clear,
|
|
input logic clk,
|
|
input logic clken,
|
|
input logic rawclk,
|
|
input logic rst_l,
|
|
input logic scan_mode,
|
|
output logic [WIDTH-1:0] dout
|
|
);
|
|
|
|
`ifdef RV_FPGA_OPTIMIZE
|
|
rvdffs #(WIDTH) dffs (.clk(rawclk), .din(din[WIDTH-1:0] & {WIDTH{~clear}}),.en((en | clear) & clken), .*);
|
|
`else
|
|
rvdffsc #(WIDTH) dffsc (.*);
|
|
`endif
|
|
|
|
endmodule
|
|
|
|
|
|
module `TEC_RV_ICG
|
|
(
|
|
input logic TE, E, CP,
|
|
output Q
|
|
);
|
|
|
|
logic en_ff;
|
|
logic enable;
|
|
|
|
assign enable = E | TE;
|
|
|
|
`ifdef VERILATOR
|
|
always @(negedge CP) begin
|
|
en_ff <= enable;
|
|
end
|
|
`else
|
|
always @(CP, enable) begin
|
|
if(!CP)
|
|
en_ff = enable;
|
|
end
|
|
`endif
|
|
assign Q = CP & en_ff;
|
|
|
|
endmodule
|
|
|
|
`ifndef RV_FPGA_OPTIMIZE
|
|
module rvclkhdr
|
|
(
|
|
input logic en,
|
|
input logic clk,
|
|
input logic scan_mode,
|
|
output logic l1clk
|
|
);
|
|
|
|
logic TE;
|
|
assign TE = scan_mode;
|
|
|
|
`TEC_RV_ICG clkhdr ( .*, .E(en), .CP(clk), .Q(l1clk));
|
|
|
|
endmodule // rvclkhdr
|
|
`endif
|
|
|
|
module rvoclkhdr
|
|
(
|
|
input logic en,
|
|
input logic clk,
|
|
input logic scan_mode,
|
|
output logic l1clk
|
|
);
|
|
|
|
logic TE;
|
|
assign TE = scan_mode;
|
|
|
|
`ifdef RV_FPGA_OPTIMIZE
|
|
assign l1clk = clk;
|
|
`else
|
|
`TEC_RV_ICG rvclkhdr ( .*, .E(en), .CP(clk), .Q(l1clk));
|
|
`endif
|
|
|
|
endmodule
|
|
|
|
module rvdffe #( parameter WIDTH=1, parameter OVERRIDE=0 )
|
|
(
|
|
input logic [WIDTH-1:0] din,
|
|
input logic en,
|
|
input logic clk,
|
|
input logic rst_l,
|
|
input logic scan_mode,
|
|
output logic [WIDTH-1:0] dout
|
|
);
|
|
|
|
logic l1clk;
|
|
|
|
|
|
`ifndef PHYSICAL
|
|
if (WIDTH >= 8 || OVERRIDE==1) begin: genblock
|
|
`endif
|
|
|
|
`ifdef RV_FPGA_OPTIMIZE
|
|
rvdffs #(WIDTH) dff ( .* );
|
|
`else
|
|
rvclkhdr clkhdr ( .* );
|
|
rvdff #(WIDTH) dff (.*, .clk(l1clk));
|
|
`endif
|
|
|
|
`ifndef PHYSICAL
|
|
end
|
|
else
|
|
$error("%m: rvdffe width must be >= 8");
|
|
`endif
|
|
|
|
|
|
endmodule // rvdffe
|
|
|
|
module rvsyncss #(parameter WIDTH = 251)
|
|
(
|
|
input logic clk,
|
|
input logic rst_l,
|
|
input logic [WIDTH-1:0] din,
|
|
output logic [WIDTH-1:0] dout
|
|
);
|
|
|
|
logic [WIDTH-1:0] din_ff1;
|
|
|
|
rvdff #(WIDTH) sync_ff1 (.*, .din (din[WIDTH-1:0]), .dout(din_ff1[WIDTH-1:0]));
|
|
rvdff #(WIDTH) sync_ff2 (.*, .din (din_ff1[WIDTH-1:0]), .dout(dout[WIDTH-1:0]));
|
|
|
|
endmodule // rvsyncss
|
|
|
|
module rvlsadder
|
|
(
|
|
input logic [31:0] rs1,
|
|
input logic [11:0] offset,
|
|
|
|
output logic [31:0] dout
|
|
);
|
|
|
|
logic cout;
|
|
logic sign;
|
|
|
|
logic [31:12] rs1_inc;
|
|
logic [31:12] rs1_dec;
|
|
|
|
assign {cout,dout[11:0]} = {1'b0,rs1[11:0]} + {1'b0,offset[11:0]};
|
|
|
|
assign rs1_inc[31:12] = rs1[31:12] + 1;
|
|
|
|
assign rs1_dec[31:12] = rs1[31:12] - 1;
|
|
|
|
assign sign = offset[11];
|
|
|
|
assign dout[31:12] = ({20{ sign ^~ cout}} & rs1[31:12]) |
|
|
({20{ ~sign & cout}} & rs1_inc[31:12]) |
|
|
({20{ sign & ~cout}} & rs1_dec[31:12]);
|
|
|
|
endmodule // rvlsadder
|
|
|
|
// assume we only maintain pc[31:1] in the pipe
|
|
|
|
module rvbradder
|
|
(
|
|
input [31:1] pc,
|
|
input [12:1] offset,
|
|
|
|
output [31:1] dout
|
|
);
|
|
|
|
logic cout;
|
|
logic sign;
|
|
|
|
logic [31:13] pc_inc;
|
|
logic [31:13] pc_dec;
|
|
|
|
assign {cout,dout[12:1]} = {1'b0,pc[12:1]} + {1'b0,offset[12:1]};
|
|
|
|
assign pc_inc[31:13] = pc[31:13] + 1;
|
|
|
|
assign pc_dec[31:13] = pc[31:13] - 1;
|
|
|
|
assign sign = offset[12];
|
|
|
|
|
|
assign dout[31:13] = ({19{ sign ^~ cout}} & pc[31:13]) |
|
|
({19{ ~sign & cout}} & pc_inc[31:13]) |
|
|
({19{ sign & ~cout}} & pc_dec[31:13]);
|
|
|
|
|
|
endmodule // rvbradder
|
|
|
|
|
|
// 2s complement circuit
|
|
module rvtwoscomp #( parameter WIDTH=32 )
|
|
(
|
|
input logic [WIDTH-1:0] din,
|
|
|
|
output logic [WIDTH-1:0] dout
|
|
);
|
|
|
|
logic [WIDTH-1:1] dout_temp; // holding for all other bits except for the lsb. LSB is always din
|
|
|
|
genvar i;
|
|
|
|
for ( i = 1; i < WIDTH; i++ ) begin : flip_after_first_one
|
|
assign dout_temp[i] = (|din[i-1:0]) ? ~din[i] : din[i];
|
|
end : flip_after_first_one
|
|
|
|
assign dout[WIDTH-1:0] = { dout_temp[WIDTH-1:1], din[0] };
|
|
|
|
endmodule // 2'scomp
|
|
|
|
// find first
|
|
module rvfindfirst1 #( parameter WIDTH=32, SHIFT=$clog2(WIDTH) )
|
|
(
|
|
input logic [WIDTH-1:0] din,
|
|
|
|
output logic [SHIFT-1:0] dout
|
|
);
|
|
logic done;
|
|
|
|
always_comb begin
|
|
dout[SHIFT-1:0] = {SHIFT{1'b0}};
|
|
done = 1'b0;
|
|
|
|
for ( int i = WIDTH-1; i > 0; i-- ) begin : find_first_one
|
|
done |= din[i];
|
|
dout[SHIFT-1:0] += done ? 1'b0 : 1'b1;
|
|
end : find_first_one
|
|
end
|
|
endmodule // rvfindfirst1
|
|
|
|
module rvfindfirst1hot #( parameter WIDTH=32 )
|
|
(
|
|
input logic [WIDTH-1:0] din,
|
|
|
|
output logic [WIDTH-1:0] dout
|
|
);
|
|
logic done;
|
|
|
|
always_comb begin
|
|
dout[WIDTH-1:0] = {WIDTH{1'b0}};
|
|
done = 1'b0;
|
|
for ( int i = 0; i < WIDTH; i++ ) begin : find_first_one
|
|
dout[i] = ~done & din[i];
|
|
done |= din[i];
|
|
end : find_first_one
|
|
end
|
|
endmodule // rvfindfirst1hot
|
|
|
|
// mask and match function matches bits after finding the first 0 position
|
|
// find first starting from LSB. Skip that location and match the rest of the bits
|
|
module rvmaskandmatch #( parameter WIDTH=32 )
|
|
(
|
|
input logic [WIDTH-1:0] mask, // this will have the mask in the lower bit positions
|
|
input logic [WIDTH-1:0] data, // this is what needs to be matched on the upper bits with the mask's upper bits
|
|
input logic masken, // when 1 : do mask. 0 : full match
|
|
output logic match
|
|
);
|
|
|
|
logic [WIDTH-1:0] matchvec;
|
|
logic masken_or_fullmask;
|
|
|
|
assign masken_or_fullmask = masken & ~(&mask[WIDTH-1:0]);
|
|
|
|
assign matchvec[0] = masken_or_fullmask | (mask[0] == data[0]);
|
|
genvar i;
|
|
|
|
for ( i = 1; i < WIDTH; i++ ) begin : match_after_first_zero
|
|
assign matchvec[i] = (&mask[i-1:0] & masken_or_fullmask) ? 1'b1 : (mask[i] == data[i]);
|
|
end : match_after_first_zero
|
|
|
|
assign match = &matchvec[WIDTH-1:0]; // all bits either matched or were masked off
|
|
|
|
endmodule // rvmaskandmatch
|
|
|
|
module rvbtb_tag_hash (
|
|
input logic [31:1] pc,
|
|
output logic [`RV_BTB_BTAG_SIZE-1:0] hash
|
|
);
|
|
`ifndef RV_BTB_BTAG_FOLD
|
|
assign hash = {(pc[`RV_BTB_ADDR_HI+`RV_BTB_BTAG_SIZE+`RV_BTB_BTAG_SIZE+`RV_BTB_BTAG_SIZE:`RV_BTB_ADDR_HI+`RV_BTB_BTAG_SIZE+`RV_BTB_BTAG_SIZE+1] ^
|
|
pc[`RV_BTB_ADDR_HI+`RV_BTB_BTAG_SIZE+`RV_BTB_BTAG_SIZE:`RV_BTB_ADDR_HI+`RV_BTB_BTAG_SIZE+1] ^
|
|
pc[`RV_BTB_ADDR_HI+`RV_BTB_BTAG_SIZE:`RV_BTB_ADDR_HI+1])};
|
|
`else
|
|
assign hash = {(
|
|
pc[`RV_BTB_ADDR_HI+`RV_BTB_BTAG_SIZE+`RV_BTB_BTAG_SIZE:`RV_BTB_ADDR_HI+`RV_BTB_BTAG_SIZE+1] ^
|
|
pc[`RV_BTB_ADDR_HI+`RV_BTB_BTAG_SIZE:`RV_BTB_ADDR_HI+1])};
|
|
`endif
|
|
|
|
// assign hash = {pc[`RV_BTB_ADDR_HI+1],(pc[`RV_BTB_ADDR_HI+13:`RV_BTB_ADDR_HI+10] ^
|
|
// pc[`RV_BTB_ADDR_HI+9:`RV_BTB_ADDR_HI+6] ^
|
|
// pc[`RV_BTB_ADDR_HI+5:`RV_BTB_ADDR_HI+2])};
|
|
|
|
endmodule
|
|
|
|
module rvbtb_addr_hash (
|
|
input logic [31:1] pc,
|
|
output logic [`RV_BTB_ADDR_HI:`RV_BTB_ADDR_LO] hash
|
|
);
|
|
|
|
assign hash[`RV_BTB_ADDR_HI:`RV_BTB_ADDR_LO] = pc[`RV_BTB_INDEX1_HI:`RV_BTB_INDEX1_LO] ^
|
|
|
|
`ifndef RV_BTB_FOLD2_INDEX_HASH
|
|
pc[`RV_BTB_INDEX2_HI:`RV_BTB_INDEX2_LO] ^
|
|
`endif
|
|
|
|
pc[`RV_BTB_INDEX3_HI:`RV_BTB_INDEX3_LO];
|
|
|
|
endmodule
|
|
|
|
module rvbtb_ghr_hash (
|
|
input logic [`RV_BTB_ADDR_HI:`RV_BTB_ADDR_LO] hashin,
|
|
input logic [`RV_BHT_GHR_RANGE] ghr,
|
|
output logic [`RV_BHT_ADDR_HI:`RV_BHT_ADDR_LO] hash
|
|
);
|
|
|
|
// The hash function is too complex to write in verilog for all cases.
|
|
// The config script generates the logic string based on the bp config.
|
|
assign hash[`RV_BHT_ADDR_HI:`RV_BHT_ADDR_LO] = `RV_BHT_HASH_STRING;
|
|
|
|
endmodule
|
|
|
|
|
|
// Check if the S_ADDR <= addr < E_ADDR
|
|
module rvrangecheck #(CCM_SADR = 32'h0,
|
|
CCM_SIZE = 128) (
|
|
input logic [31:0] addr, // Address to be checked for range
|
|
output logic in_range, // S_ADDR <= start_addr < E_ADDR
|
|
output logic in_region
|
|
);
|
|
|
|
localparam REGION_BITS = 4;
|
|
localparam MASK_BITS = 10 + $clog2(CCM_SIZE);
|
|
|
|
logic [31:0] start_addr;
|
|
logic [3:0] region;
|
|
|
|
assign start_addr[31:0] = CCM_SADR;
|
|
assign region[REGION_BITS-1:0] = start_addr[31:(32-REGION_BITS)];
|
|
|
|
assign in_region = (addr[31:(32-REGION_BITS)] == region[REGION_BITS-1:0]);
|
|
if (CCM_SIZE == 48)
|
|
assign in_range = (addr[31:MASK_BITS] == start_addr[31:MASK_BITS]) & ~(&addr[MASK_BITS-1 : MASK_BITS-2]);
|
|
else
|
|
assign in_range = (addr[31:MASK_BITS] == start_addr[31:MASK_BITS]);
|
|
|
|
endmodule // rvrangechecker
|
|
|
|
// 16 bit even parity generator
|
|
module rveven_paritygen #(WIDTH = 16) (
|
|
input logic [WIDTH-1:0] data_in, // Data
|
|
output logic parity_out // generated even parity
|
|
);
|
|
|
|
assign parity_out = ^(data_in[WIDTH-1:0]) ;
|
|
|
|
endmodule // rveven_paritygen
|
|
|
|
module rveven_paritycheck #(WIDTH = 16) (
|
|
input logic [WIDTH-1:0] data_in, // Data
|
|
input logic parity_in,
|
|
output logic parity_err // Parity error
|
|
);
|
|
|
|
assign parity_err = ^(data_in[WIDTH-1:0]) ^ parity_in ;
|
|
|
|
endmodule // rveven_paritycheck
|
|
|
|
module rvecc_encode (
|
|
input [31:0] din,
|
|
output [6:0] ecc_out
|
|
);
|
|
logic [5:0] ecc_out_temp;
|
|
|
|
assign ecc_out_temp[0] = din[0]^din[1]^din[3]^din[4]^din[6]^din[8]^din[10]^din[11]^din[13]^din[15]^din[17]^din[19]^din[21]^din[23]^din[25]^din[26]^din[28]^din[30];
|
|
assign ecc_out_temp[1] = din[0]^din[2]^din[3]^din[5]^din[6]^din[9]^din[10]^din[12]^din[13]^din[16]^din[17]^din[20]^din[21]^din[24]^din[25]^din[27]^din[28]^din[31];
|
|
assign ecc_out_temp[2] = din[1]^din[2]^din[3]^din[7]^din[8]^din[9]^din[10]^din[14]^din[15]^din[16]^din[17]^din[22]^din[23]^din[24]^din[25]^din[29]^din[30]^din[31];
|
|
assign ecc_out_temp[3] = din[4]^din[5]^din[6]^din[7]^din[8]^din[9]^din[10]^din[18]^din[19]^din[20]^din[21]^din[22]^din[23]^din[24]^din[25];
|
|
assign ecc_out_temp[4] = din[11]^din[12]^din[13]^din[14]^din[15]^din[16]^din[17]^din[18]^din[19]^din[20]^din[21]^din[22]^din[23]^din[24]^din[25];
|
|
assign ecc_out_temp[5] = din[26]^din[27]^din[28]^din[29]^din[30]^din[31];
|
|
|
|
assign ecc_out[6:0] = {(^din[31:0])^(^ecc_out_temp[5:0]),ecc_out_temp[5:0]};
|
|
|
|
endmodule // rvecc_encode
|
|
|
|
module rvecc_decode (
|
|
input en,
|
|
input [31:0] din,
|
|
input [6:0] ecc_in,
|
|
input sed_ded, // only do detection and no correction. Used for the I$
|
|
output [31:0] dout,
|
|
output [6:0] ecc_out,
|
|
output single_ecc_error,
|
|
output double_ecc_error
|
|
|
|
);
|
|
|
|
logic [6:0] ecc_check;
|
|
logic [38:0] error_mask;
|
|
logic [38:0] din_plus_parity, dout_plus_parity;
|
|
|
|
// Generate the ecc bits
|
|
assign ecc_check[0] = ecc_in[0]^din[0]^din[1]^din[3]^din[4]^din[6]^din[8]^din[10]^din[11]^din[13]^din[15]^din[17]^din[19]^din[21]^din[23]^din[25]^din[26]^din[28]^din[30];
|
|
assign ecc_check[1] = ecc_in[1]^din[0]^din[2]^din[3]^din[5]^din[6]^din[9]^din[10]^din[12]^din[13]^din[16]^din[17]^din[20]^din[21]^din[24]^din[25]^din[27]^din[28]^din[31];
|
|
assign ecc_check[2] = ecc_in[2]^din[1]^din[2]^din[3]^din[7]^din[8]^din[9]^din[10]^din[14]^din[15]^din[16]^din[17]^din[22]^din[23]^din[24]^din[25]^din[29]^din[30]^din[31];
|
|
assign ecc_check[3] = ecc_in[3]^din[4]^din[5]^din[6]^din[7]^din[8]^din[9]^din[10]^din[18]^din[19]^din[20]^din[21]^din[22]^din[23]^din[24]^din[25];
|
|
assign ecc_check[4] = ecc_in[4]^din[11]^din[12]^din[13]^din[14]^din[15]^din[16]^din[17]^din[18]^din[19]^din[20]^din[21]^din[22]^din[23]^din[24]^din[25];
|
|
assign ecc_check[5] = ecc_in[5]^din[26]^din[27]^din[28]^din[29]^din[30]^din[31];
|
|
|
|
// This is the parity bit
|
|
assign ecc_check[6] = ((^din[31:0])^(^ecc_in[6:0])) & ~sed_ded;
|
|
|
|
assign single_ecc_error = en & (ecc_check[6:0] != 0) & ecc_check[6]; // this will never be on for sed_ded
|
|
assign double_ecc_error = en & (ecc_check[6:0] != 0) & ~ecc_check[6]; // all errors in the sed_ded case will be recorded as DE
|
|
|
|
// Generate the mask for error correctiong
|
|
for (genvar i=1; i<40; i++) begin
|
|
assign error_mask[i-1] = (ecc_check[5:0] == i);
|
|
end
|
|
|
|
// Generate the corrected data
|
|
assign din_plus_parity[38:0] = {ecc_in[6], din[31:26], ecc_in[5], din[25:11], ecc_in[4], din[10:4], ecc_in[3], din[3:1], ecc_in[2], din[0], ecc_in[1:0]};
|
|
|
|
assign dout_plus_parity[38:0] = single_ecc_error ? (error_mask[38:0] ^ din_plus_parity[38:0]) : din_plus_parity[38:0];
|
|
assign dout[31:0] = {dout_plus_parity[37:32], dout_plus_parity[30:16], dout_plus_parity[14:8], dout_plus_parity[6:4], dout_plus_parity[2]};
|
|
assign ecc_out[6:0] = {(dout_plus_parity[38] ^ (ecc_check[6:0] == 7'b1000000)), dout_plus_parity[31], dout_plus_parity[15], dout_plus_parity[7], dout_plus_parity[3], dout_plus_parity[1:0]};
|
|
|
|
endmodule // rvecc_decode
|