cores-swerv-el2/design/lib/beh_lib.sv

815 lines
24 KiB
Systemverilog

// SPDX-License-Identifier: Apache-2.0
// Copyright 2020 Western Digital Corporation or its affiliates.
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// all flops call the rvdff flop
module rvdff #( parameter WIDTH=1, SHORT=0 )
(
input logic [WIDTH-1:0] din,
input logic clk,
input logic rst_l,
output logic [WIDTH-1:0] dout
);
if (SHORT == 1) begin
assign dout = din;
end
else begin
`ifdef RV_CLOCKGATE
always @(posedge tb_top.clk) begin
#0 $strobe("CG: %0t %m din %x dout %x clk %b width %d",$time,din,dout,clk,WIDTH);
end
`endif
always_ff @(posedge clk or negedge rst_l) begin
if (rst_l == 0)
dout[WIDTH-1:0] <= 0;
else
dout[WIDTH-1:0] <= din[WIDTH-1:0];
end
end
endmodule
// rvdff with 2:1 input mux to flop din iff sel==1
module rvdffs #( parameter WIDTH=1, SHORT=0 )
(
input logic [WIDTH-1:0] din,
input logic en,
input logic clk,
input logic rst_l,
output logic [WIDTH-1:0] dout
);
if (SHORT == 1) begin : genblock
assign dout = din;
end
else begin : genblock
rvdff #(WIDTH) dffs (.din((en) ? din[WIDTH-1:0] : dout[WIDTH-1:0]), .*);
end
endmodule
// rvdff with en and clear
module rvdffsc #( parameter WIDTH=1, SHORT=0 )
(
input logic [WIDTH-1:0] din,
input logic en,
input logic clear,
input logic clk,
input logic rst_l,
output logic [WIDTH-1:0] dout
);
logic [WIDTH-1:0] din_new;
if (SHORT == 1) begin
assign dout = din;
end
else begin
assign din_new = {WIDTH{~clear}} & (en ? din[WIDTH-1:0] : dout[WIDTH-1:0]);
rvdff #(WIDTH) dffsc (.din(din_new[WIDTH-1:0]), .*);
end
endmodule
// _fpga versions
module rvdff_fpga #( parameter WIDTH=1, SHORT=0 )
(
input logic [WIDTH-1:0] din,
input logic clk,
input logic clken,
input logic rawclk,
input logic rst_l,
output logic [WIDTH-1:0] dout
);
if (SHORT == 1) begin
assign dout = din;
end
else begin
`ifdef RV_FPGA_OPTIMIZE
rvdffs #(WIDTH) dffs (.clk(rawclk), .en(clken), .*);
`else
rvdff #(WIDTH) dff (.*);
`endif
end
endmodule
// rvdff with 2:1 input mux to flop din iff sel==1
module rvdffs_fpga #( parameter WIDTH=1, SHORT=0 )
(
input logic [WIDTH-1:0] din,
input logic en,
input logic clk,
input logic clken,
input logic rawclk,
input logic rst_l,
output logic [WIDTH-1:0] dout
);
if (SHORT == 1) begin : genblock
assign dout = din;
end
else begin : genblock
`ifdef RV_FPGA_OPTIMIZE
rvdffs #(WIDTH) dffs (.clk(rawclk), .en(clken & en), .*);
`else
rvdffs #(WIDTH) dffs (.*);
`endif
end
endmodule
// rvdff with en and clear
module rvdffsc_fpga #( parameter WIDTH=1, SHORT=0 )
(
input logic [WIDTH-1:0] din,
input logic en,
input logic clear,
input logic clk,
input logic clken,
input logic rawclk,
input logic rst_l,
output logic [WIDTH-1:0] dout
);
logic [WIDTH-1:0] din_new;
if (SHORT == 1) begin
assign dout = din;
end
else begin
`ifdef RV_FPGA_OPTIMIZE
rvdffs #(WIDTH) dffs (.clk(rawclk), .din(din[WIDTH-1:0] & {WIDTH{~clear}}),.en((en | clear) & clken), .*);
`else
rvdffsc #(WIDTH) dffsc (.*);
`endif
end
endmodule
module rvdffe #( parameter WIDTH=1, SHORT=0, OVERRIDE=0 )
(
input logic [WIDTH-1:0] din,
input logic en,
input logic clk,
input logic rst_l,
input logic scan_mode,
output logic [WIDTH-1:0] dout
);
logic l1clk;
if (SHORT == 1) begin : genblock
if (1) begin : genblock
assign dout = din;
end
end
else begin : genblock
`ifndef RV_PHYSICAL
if (WIDTH >= 8 || OVERRIDE==1) begin: genblock
`endif
`ifdef RV_FPGA_OPTIMIZE
rvdffs #(WIDTH) dff ( .* );
`else
rvclkhdr clkhdr ( .* );
rvdff #(WIDTH) dff (.*, .clk(l1clk));
`endif
`ifndef RV_PHYSICAL
end
else
$error("%m: rvdffe must be WIDTH >= 8");
`endif
end // else: !if(SHORT == 1)
endmodule // rvdffe
module rvdffpcie #( parameter WIDTH=31 )
(
input logic [WIDTH-1:0] din,
input logic clk,
input logic rst_l,
input logic en,
input logic scan_mode,
output logic [WIDTH-1:0] dout
);
`ifndef RV_PHYSICAL
if (WIDTH == 31) begin: genblock
`endif
`ifdef RV_FPGA_OPTIMIZE
rvdffs #(WIDTH) dff ( .* );
`else
rvdfflie #(.WIDTH(WIDTH), .LEFT(19)) dff (.*);
`endif
`ifndef RV_PHYSICAL
end
else
$error("%m: rvdffpcie width must be 31");
`endif
endmodule
// format: { LEFT, EXTRA }
// LEFT # of bits will be done with rvdffie, all else EXTRA with rvdffe
module rvdfflie #( parameter WIDTH=16, LEFT=8 )
(
input logic [WIDTH-1:0] din,
input logic clk,
input logic rst_l,
input logic en,
input logic scan_mode,
output logic [WIDTH-1:0] dout
);
localparam EXTRA = WIDTH-LEFT;
localparam LMSB = WIDTH-1;
localparam LLSB = LMSB-LEFT+1;
localparam XMSB = LLSB-1;
localparam XLSB = LLSB-EXTRA;
`ifndef RV_PHYSICAL
if (WIDTH >= 16 && LEFT >= 8 && EXTRA >= 8) begin: genblock
`endif
`ifdef RV_FPGA_OPTIMIZE
rvdffs #(WIDTH) dff ( .* );
`else
rvdffiee #(LEFT) dff_left (.*, .din(din[LMSB:LLSB]), .dout(dout[LMSB:LLSB]));
rvdffe #(EXTRA) dff_extra (.*, .din(din[XMSB:XLSB]), .dout(dout[XMSB:XLSB]));
`endif
`ifndef RV_PHYSICAL
end
else
$error("%m: rvdfflie musb be WIDTH >= 16 && LEFT >= 8 && EXTRA >= 8");
`endif
endmodule
// special power flop for predict packet
// format: { LEFT, RIGHT==31 }
// LEFT # of bits will be done with rvdffe; RIGHT is enabled by LEFT[LSB] & en
module rvdffppe #( parameter WIDTH=32 )
(
input logic [WIDTH-1:0] din,
input logic clk,
input logic rst_l,
input logic en,
input logic scan_mode,
output logic [WIDTH-1:0] dout
);
localparam RIGHT = 31;
localparam LEFT = WIDTH - RIGHT;
localparam LMSB = WIDTH-1;
localparam LLSB = LMSB-LEFT+1;
localparam RMSB = LLSB-1;
localparam RLSB = LLSB-RIGHT;
`ifndef RV_PHYSICAL
if (WIDTH>=32 && LEFT>=8 && RIGHT>=8) begin: genblock
`endif
`ifdef RV_FPGA_OPTIMIZE
rvdffs #(WIDTH) dff ( .* );
`else
rvdffe #(LEFT) dff_left (.*, .din(din[LMSB:LLSB]), .dout(dout[LMSB:LLSB]));
rvdffe #(RIGHT) dff_right (.*, .din(din[RMSB:RLSB]), .dout(dout[RMSB:RLSB]), .en(en & din[LLSB])); // qualify with pret
`endif
`ifndef RV_PHYSICAL
end
else
$error("%m: must be WIDTH>=32 && LEFT>=8 && RIGHT>=8");
`endif
endmodule
module rvdffie #( parameter WIDTH=1, OVERRIDE=0 )
(
input logic [WIDTH-1:0] din,
input logic clk,
input logic rst_l,
input logic scan_mode,
output logic [WIDTH-1:0] dout
);
logic l1clk;
logic en;
`ifndef RV_PHYSICAL
if (WIDTH >= 8 || OVERRIDE==1) begin: genblock
`endif
assign en = |(din ^ dout);
`ifdef RV_FPGA_OPTIMIZE
rvdffs #(WIDTH) dff ( .* );
`else
rvclkhdr clkhdr ( .* );
rvdff #(WIDTH) dff (.*, .clk(l1clk));
`endif
`ifndef RV_PHYSICAL
end
else
$error("%m: rvdffie must be WIDTH >= 8");
`endif
endmodule
// ie flop but it has an .en input
module rvdffiee #( parameter WIDTH=1, OVERRIDE=0 )
(
input logic [WIDTH-1:0] din,
input logic clk,
input logic rst_l,
input logic scan_mode,
input logic en,
output logic [WIDTH-1:0] dout
);
logic l1clk;
logic final_en;
`ifndef RV_PHYSICAL
if (WIDTH >= 8 || OVERRIDE==1) begin: genblock
`endif
assign final_en = (|(din ^ dout)) & en;
`ifdef RV_FPGA_OPTIMIZE
rvdffs #(WIDTH) dff ( .*, .en(final_en) );
`else
rvdffe #(WIDTH) dff (.*, .en(final_en));
`endif
`ifndef RV_PHYSICAL
end
else
$error("%m: rvdffie width must be >= 8");
`endif
endmodule
module rvsyncss #(parameter WIDTH = 251)
(
input logic clk,
input logic rst_l,
input logic [WIDTH-1:0] din,
output logic [WIDTH-1:0] dout
);
logic [WIDTH-1:0] din_ff1;
rvdff #(WIDTH) sync_ff1 (.*, .din (din[WIDTH-1:0]), .dout(din_ff1[WIDTH-1:0]));
rvdff #(WIDTH) sync_ff2 (.*, .din (din_ff1[WIDTH-1:0]), .dout(dout[WIDTH-1:0]));
endmodule // rvsyncss
module rvsyncss_fpga #(parameter WIDTH = 251)
(
input logic gw_clk,
input logic rawclk,
input logic clken,
input logic rst_l,
input logic [WIDTH-1:0] din,
output logic [WIDTH-1:0] dout
);
logic [WIDTH-1:0] din_ff1;
rvdff_fpga #(WIDTH) sync_ff1 (.*, .clk(gw_clk), .rawclk(rawclk), .clken(clken), .din (din[WIDTH-1:0]), .dout(din_ff1[WIDTH-1:0]));
rvdff_fpga #(WIDTH) sync_ff2 (.*, .clk(gw_clk), .rawclk(rawclk), .clken(clken), .din (din_ff1[WIDTH-1:0]), .dout(dout[WIDTH-1:0]));
endmodule // rvsyncss
module rvlsadder
(
input logic [31:0] rs1,
input logic [11:0] offset,
output logic [31:0] dout
);
logic cout;
logic sign;
logic [31:12] rs1_inc;
logic [31:12] rs1_dec;
assign {cout,dout[11:0]} = {1'b0,rs1[11:0]} + {1'b0,offset[11:0]};
assign rs1_inc[31:12] = rs1[31:12] + 1;
assign rs1_dec[31:12] = rs1[31:12] - 1;
assign sign = offset[11];
assign dout[31:12] = ({20{ sign ^~ cout}} & rs1[31:12]) |
({20{ ~sign & cout}} & rs1_inc[31:12]) |
({20{ sign & ~cout}} & rs1_dec[31:12]);
endmodule // rvlsadder
// assume we only maintain pc[31:1] in the pipe
module rvbradder
(
input [31:1] pc,
input [12:1] offset,
output [31:1] dout
);
logic cout;
logic sign;
logic [31:13] pc_inc;
logic [31:13] pc_dec;
assign {cout,dout[12:1]} = {1'b0,pc[12:1]} + {1'b0,offset[12:1]};
assign pc_inc[31:13] = pc[31:13] + 1;
assign pc_dec[31:13] = pc[31:13] - 1;
assign sign = offset[12];
assign dout[31:13] = ({19{ sign ^~ cout}} & pc[31:13]) |
({19{ ~sign & cout}} & pc_inc[31:13]) |
({19{ sign & ~cout}} & pc_dec[31:13]);
endmodule // rvbradder
// 2s complement circuit
module rvtwoscomp #( parameter WIDTH=32 )
(
input logic [WIDTH-1:0] din,
output logic [WIDTH-1:0] dout
);
logic [WIDTH-1:1] dout_temp; // holding for all other bits except for the lsb. LSB is always din
genvar i;
for ( i = 1; i < WIDTH; i++ ) begin : flip_after_first_one
assign dout_temp[i] = (|din[i-1:0]) ? ~din[i] : din[i];
end : flip_after_first_one
assign dout[WIDTH-1:0] = { dout_temp[WIDTH-1:1], din[0] };
endmodule // 2'scomp
// find first
module rvfindfirst1 #( parameter WIDTH=32, SHIFT=$clog2(WIDTH) )
(
input logic [WIDTH-1:0] din,
output logic [SHIFT-1:0] dout
);
logic done;
always_comb begin
dout[SHIFT-1:0] = {SHIFT{1'b0}};
done = 1'b0;
for ( int i = WIDTH-1; i > 0; i-- ) begin : find_first_one
done |= din[i];
dout[SHIFT-1:0] += done ? 1'b0 : 1'b1;
end : find_first_one
end
endmodule // rvfindfirst1
module rvfindfirst1hot #( parameter WIDTH=32 )
(
input logic [WIDTH-1:0] din,
output logic [WIDTH-1:0] dout
);
logic done;
always_comb begin
dout[WIDTH-1:0] = {WIDTH{1'b0}};
done = 1'b0;
for ( int i = 0; i < WIDTH; i++ ) begin : find_first_one
dout[i] = ~done & din[i];
done |= din[i];
end : find_first_one
end
endmodule // rvfindfirst1hot
// mask and match function matches bits after finding the first 0 position
// find first starting from LSB. Skip that location and match the rest of the bits
module rvmaskandmatch #( parameter WIDTH=32 )
(
input logic [WIDTH-1:0] mask, // this will have the mask in the lower bit positions
input logic [WIDTH-1:0] data, // this is what needs to be matched on the upper bits with the mask's upper bits
input logic masken, // when 1 : do mask. 0 : full match
output logic match
);
logic [WIDTH-1:0] matchvec;
logic masken_or_fullmask;
assign masken_or_fullmask = masken & ~(&mask[WIDTH-1:0]);
assign matchvec[0] = masken_or_fullmask | (mask[0] == data[0]);
genvar i;
for ( i = 1; i < WIDTH; i++ ) begin : match_after_first_zero
assign matchvec[i] = (&mask[i-1:0] & masken_or_fullmask) ? 1'b1 : (mask[i] == data[i]);
end : match_after_first_zero
assign match = &matchvec[WIDTH-1:0]; // all bits either matched or were masked off
endmodule // rvmaskandmatch
// Check if the S_ADDR <= addr < E_ADDR
module rvrangecheck #(CCM_SADR = 32'h0,
CCM_SIZE = 128) (
input logic [31:0] addr, // Address to be checked for range
output logic in_range, // S_ADDR <= start_addr < E_ADDR
output logic in_region
);
localparam REGION_BITS = 4;
localparam MASK_BITS = 10 + $clog2(CCM_SIZE);
logic [31:0] start_addr;
logic [3:0] region;
assign start_addr[31:0] = CCM_SADR;
assign region[REGION_BITS-1:0] = start_addr[31:(32-REGION_BITS)];
assign in_region = (addr[31:(32-REGION_BITS)] == region[REGION_BITS-1:0]);
if (CCM_SIZE == 48)
assign in_range = (addr[31:MASK_BITS] == start_addr[31:MASK_BITS]) & ~(&addr[MASK_BITS-1 : MASK_BITS-2]);
else
assign in_range = (addr[31:MASK_BITS] == start_addr[31:MASK_BITS]);
endmodule // rvrangechecker
// 16 bit even parity generator
module rveven_paritygen #(WIDTH = 16) (
input logic [WIDTH-1:0] data_in, // Data
output logic parity_out // generated even parity
);
assign parity_out = ^(data_in[WIDTH-1:0]) ;
endmodule // rveven_paritygen
module rveven_paritycheck #(WIDTH = 16) (
input logic [WIDTH-1:0] data_in, // Data
input logic parity_in,
output logic parity_err // Parity error
);
assign parity_err = ^(data_in[WIDTH-1:0]) ^ parity_in ;
endmodule // rveven_paritycheck
module rvecc_encode (
input [31:0] din,
output [6:0] ecc_out
);
logic [5:0] ecc_out_temp;
assign ecc_out_temp[0] = din[0]^din[1]^din[3]^din[4]^din[6]^din[8]^din[10]^din[11]^din[13]^din[15]^din[17]^din[19]^din[21]^din[23]^din[25]^din[26]^din[28]^din[30];
assign ecc_out_temp[1] = din[0]^din[2]^din[3]^din[5]^din[6]^din[9]^din[10]^din[12]^din[13]^din[16]^din[17]^din[20]^din[21]^din[24]^din[25]^din[27]^din[28]^din[31];
assign ecc_out_temp[2] = din[1]^din[2]^din[3]^din[7]^din[8]^din[9]^din[10]^din[14]^din[15]^din[16]^din[17]^din[22]^din[23]^din[24]^din[25]^din[29]^din[30]^din[31];
assign ecc_out_temp[3] = din[4]^din[5]^din[6]^din[7]^din[8]^din[9]^din[10]^din[18]^din[19]^din[20]^din[21]^din[22]^din[23]^din[24]^din[25];
assign ecc_out_temp[4] = din[11]^din[12]^din[13]^din[14]^din[15]^din[16]^din[17]^din[18]^din[19]^din[20]^din[21]^din[22]^din[23]^din[24]^din[25];
assign ecc_out_temp[5] = din[26]^din[27]^din[28]^din[29]^din[30]^din[31];
assign ecc_out[6:0] = {(^din[31:0])^(^ecc_out_temp[5:0]),ecc_out_temp[5:0]};
endmodule // rvecc_encode
module rvecc_decode (
input en,
input [31:0] din,
input [6:0] ecc_in,
input sed_ded, // only do detection and no correction. Used for the I$
output [31:0] dout,
output [6:0] ecc_out,
output single_ecc_error,
output double_ecc_error
);
logic [6:0] ecc_check;
logic [38:0] error_mask;
logic [38:0] din_plus_parity, dout_plus_parity;
// Generate the ecc bits
assign ecc_check[0] = ecc_in[0]^din[0]^din[1]^din[3]^din[4]^din[6]^din[8]^din[10]^din[11]^din[13]^din[15]^din[17]^din[19]^din[21]^din[23]^din[25]^din[26]^din[28]^din[30];
assign ecc_check[1] = ecc_in[1]^din[0]^din[2]^din[3]^din[5]^din[6]^din[9]^din[10]^din[12]^din[13]^din[16]^din[17]^din[20]^din[21]^din[24]^din[25]^din[27]^din[28]^din[31];
assign ecc_check[2] = ecc_in[2]^din[1]^din[2]^din[3]^din[7]^din[8]^din[9]^din[10]^din[14]^din[15]^din[16]^din[17]^din[22]^din[23]^din[24]^din[25]^din[29]^din[30]^din[31];
assign ecc_check[3] = ecc_in[3]^din[4]^din[5]^din[6]^din[7]^din[8]^din[9]^din[10]^din[18]^din[19]^din[20]^din[21]^din[22]^din[23]^din[24]^din[25];
assign ecc_check[4] = ecc_in[4]^din[11]^din[12]^din[13]^din[14]^din[15]^din[16]^din[17]^din[18]^din[19]^din[20]^din[21]^din[22]^din[23]^din[24]^din[25];
assign ecc_check[5] = ecc_in[5]^din[26]^din[27]^din[28]^din[29]^din[30]^din[31];
// This is the parity bit
assign ecc_check[6] = ((^din[31:0])^(^ecc_in[6:0])) & ~sed_ded;
assign single_ecc_error = en & (ecc_check[6:0] != 0) & ecc_check[6]; // this will never be on for sed_ded
assign double_ecc_error = en & (ecc_check[6:0] != 0) & ~ecc_check[6]; // all errors in the sed_ded case will be recorded as DE
// Generate the mask for error correctiong
for (genvar i=1; i<40; i++) begin
assign error_mask[i-1] = (ecc_check[5:0] == i);
end
// Generate the corrected data
assign din_plus_parity[38:0] = {ecc_in[6], din[31:26], ecc_in[5], din[25:11], ecc_in[4], din[10:4], ecc_in[3], din[3:1], ecc_in[2], din[0], ecc_in[1:0]};
assign dout_plus_parity[38:0] = single_ecc_error ? (error_mask[38:0] ^ din_plus_parity[38:0]) : din_plus_parity[38:0];
assign dout[31:0] = {dout_plus_parity[37:32], dout_plus_parity[30:16], dout_plus_parity[14:8], dout_plus_parity[6:4], dout_plus_parity[2]};
assign ecc_out[6:0] = {(dout_plus_parity[38] ^ (ecc_check[6:0] == 7'b1000000)), dout_plus_parity[31], dout_plus_parity[15], dout_plus_parity[7], dout_plus_parity[3], dout_plus_parity[1:0]};
endmodule // rvecc_decode
module rvecc_encode_64 (
input [63:0] din,
output [6:0] ecc_out
);
assign ecc_out[0] = din[0]^din[1]^din[3]^din[4]^din[6]^din[8]^din[10]^din[11]^din[13]^din[15]^din[17]^din[19]^din[21]^din[23]^din[25]^din[26]^din[28]^din[30]^din[32]^din[34]^din[36]^din[38]^din[40]^din[42]^din[44]^din[46]^din[48]^din[50]^din[52]^din[54]^din[56]^din[57]^din[59]^din[61]^din[63];
assign ecc_out[1] = din[0]^din[2]^din[3]^din[5]^din[6]^din[9]^din[10]^din[12]^din[13]^din[16]^din[17]^din[20]^din[21]^din[24]^din[25]^din[27]^din[28]^din[31]^din[32]^din[35]^din[36]^din[39]^din[40]^din[43]^din[44]^din[47]^din[48]^din[51]^din[52]^din[55]^din[56]^din[58]^din[59]^din[62]^din[63];
assign ecc_out[2] = din[1]^din[2]^din[3]^din[7]^din[8]^din[9]^din[10]^din[14]^din[15]^din[16]^din[17]^din[22]^din[23]^din[24]^din[25]^din[29]^din[30]^din[31]^din[32]^din[37]^din[38]^din[39]^din[40]^din[45]^din[46]^din[47]^din[48]^din[53]^din[54]^din[55]^din[56]^din[60]^din[61]^din[62]^din[63];
assign ecc_out[3] = din[4]^din[5]^din[6]^din[7]^din[8]^din[9]^din[10]^din[18]^din[19]^din[20]^din[21]^din[22]^din[23]^din[24]^din[25]^din[33]^din[34]^din[35]^din[36]^din[37]^din[38]^din[39]^din[40]^din[49]^din[50]^din[51]^din[52]^din[53]^din[54]^din[55]^din[56];
assign ecc_out[4] = din[11]^din[12]^din[13]^din[14]^din[15]^din[16]^din[17]^din[18]^din[19]^din[20]^din[21]^din[22]^din[23]^din[24]^din[25]^din[41]^din[42]^din[43]^din[44]^din[45]^din[46]^din[47]^din[48]^din[49]^din[50]^din[51]^din[52]^din[53]^din[54]^din[55]^din[56];
assign ecc_out[5] = din[26]^din[27]^din[28]^din[29]^din[30]^din[31]^din[32]^din[33]^din[34]^din[35]^din[36]^din[37]^din[38]^din[39]^din[40]^din[41]^din[42]^din[43]^din[44]^din[45]^din[46]^din[47]^din[48]^din[49]^din[50]^din[51]^din[52]^din[53]^din[54]^din[55]^din[56];
assign ecc_out[6] = din[57]^din[58]^din[59]^din[60]^din[61]^din[62]^din[63];
endmodule // rvecc_encode_64
module rvecc_decode_64 (
input en,
input [63:0] din,
input [6:0] ecc_in,
output ecc_error
);
logic [6:0] ecc_check;
// Generate the ecc bits
assign ecc_check[0] = ecc_in[0]^din[0]^din[1]^din[3]^din[4]^din[6]^din[8]^din[10]^din[11]^din[13]^din[15]^din[17]^din[19]^din[21]^din[23]^din[25]^din[26]^din[28]^din[30]^din[32]^din[34]^din[36]^din[38]^din[40]^din[42]^din[44]^din[46]^din[48]^din[50]^din[52]^din[54]^din[56]^din[57]^din[59]^din[61]^din[63];
assign ecc_check[1] = ecc_in[1]^din[0]^din[2]^din[3]^din[5]^din[6]^din[9]^din[10]^din[12]^din[13]^din[16]^din[17]^din[20]^din[21]^din[24]^din[25]^din[27]^din[28]^din[31]^din[32]^din[35]^din[36]^din[39]^din[40]^din[43]^din[44]^din[47]^din[48]^din[51]^din[52]^din[55]^din[56]^din[58]^din[59]^din[62]^din[63];
assign ecc_check[2] = ecc_in[2]^din[1]^din[2]^din[3]^din[7]^din[8]^din[9]^din[10]^din[14]^din[15]^din[16]^din[17]^din[22]^din[23]^din[24]^din[25]^din[29]^din[30]^din[31]^din[32]^din[37]^din[38]^din[39]^din[40]^din[45]^din[46]^din[47]^din[48]^din[53]^din[54]^din[55]^din[56]^din[60]^din[61]^din[62]^din[63];
assign ecc_check[3] = ecc_in[3]^din[4]^din[5]^din[6]^din[7]^din[8]^din[9]^din[10]^din[18]^din[19]^din[20]^din[21]^din[22]^din[23]^din[24]^din[25]^din[33]^din[34]^din[35]^din[36]^din[37]^din[38]^din[39]^din[40]^din[49]^din[50]^din[51]^din[52]^din[53]^din[54]^din[55]^din[56];
assign ecc_check[4] = ecc_in[4]^din[11]^din[12]^din[13]^din[14]^din[15]^din[16]^din[17]^din[18]^din[19]^din[20]^din[21]^din[22]^din[23]^din[24]^din[25]^din[41]^din[42]^din[43]^din[44]^din[45]^din[46]^din[47]^din[48]^din[49]^din[50]^din[51]^din[52]^din[53]^din[54]^din[55]^din[56];
assign ecc_check[5] = ecc_in[5]^din[26]^din[27]^din[28]^din[29]^din[30]^din[31]^din[32]^din[33]^din[34]^din[35]^din[36]^din[37]^din[38]^din[39]^din[40]^din[41]^din[42]^din[43]^din[44]^din[45]^din[46]^din[47]^din[48]^din[49]^din[50]^din[51]^din[52]^din[53]^din[54]^din[55]^din[56];
assign ecc_check[6] = ecc_in[6]^din[57]^din[58]^din[59]^din[60]^din[61]^din[62]^din[63];
assign ecc_error = en & (ecc_check[6:0] != 0); // all errors in the sed_ded case will be recorded as DE
endmodule // rvecc_decode_64
module `TEC_RV_ICG
(
input logic SE, EN, CK,
output Q
);
logic en_ff;
logic enable;
assign enable = EN | SE;
`ifdef VERILATOR
always @(negedge CK) begin
en_ff <= enable;
end
`else
always @(CK, enable) begin
if(!CK)
en_ff = enable;
end
`endif
assign Q = CK & en_ff;
endmodule
`ifndef RV_FPGA_OPTIMIZE
module rvclkhdr
(
input logic en,
input logic clk,
input logic scan_mode,
output logic l1clk
);
logic SE;
assign SE = 0;
`TEC_RV_ICG clkhdr ( .*, .EN(en), .CK(clk), .Q(l1clk));
endmodule // rvclkhdr
`endif
module rvoclkhdr
(
input logic en,
input logic clk,
input logic scan_mode,
output logic l1clk
);
logic SE;
assign SE = 0;
`ifdef RV_FPGA_OPTIMIZE
assign l1clk = clk;
`else
`TEC_RV_ICG clkhdr ( .*, .EN(en), .CK(clk), .Q(l1clk));
`endif
endmodule