deskhop/pico-sdk/lib/tinyusb/hw/bsp/rp2040/family.c

/*
 * The MIT License (MIT)
 *
 * Copyright (c) 2020 Raspberry Pi (Trading) Ltd.
 * Copyright (c) 2021, Ha Thach (tinyusb.org)
 *
 * Permission is hereby granted, free of charge, to any person obtaining a copy
 * of this software and associated documentation files (the "Software"), to deal
 * in the Software without restriction, including without limitation the rights
 * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
 * copies of the Software, and to permit persons to whom the Software is
 * furnished to do so, subject to the following conditions:
 *
 * The above copyright notice and this permission notice shall be included in
 * all copies or substantial portions of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
 * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
 * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
 * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
 * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
 * THE SOFTWARE.
 *
 * This file is part of the TinyUSB stack.
 */

#include "pico/stdlib.h"
#include "pico/binary_info.h"
#include "pico/unique_id.h"
#include "hardware/gpio.h"
#include "hardware/sync.h"
#include "hardware/resets.h"
#include "hardware/structs/ioqspi.h"
#include "hardware/structs/sio.h"

#include "bsp/board_api.h"
#include "board.h"

#ifdef UART_DEV
static uart_inst_t *uart_inst;
#endif

#if CFG_TUH_RPI_PIO_USB || CFG_TUD_RPI_PIO_USB
#include "pio_usb.h"
#endif

#if CFG_TUH_ENABLED && CFG_TUH_MAX3421
#include "hardware/spi.h"
static void max3421_init(void);
#endif

#ifdef BUTTON_BOOTSEL
// This example blinks the Picoboard LED when the BOOTSEL button is pressed.
//
// Picoboard has a button attached to the flash CS pin, which the bootrom
// checks, and jumps straight to the USB bootcode if the button is pressed
// (pulling flash CS low). We can check this pin in by jumping to some code in
// SRAM (so that the XIP interface is not required), floating the flash CS
// pin, and observing whether it is pulled low.
//
// This doesn't work if others are trying to access flash at the same time,
// e.g. XIP streamer, or the other core.
bool __no_inline_not_in_flash_func(get_bootsel_button)(void) {
  const uint CS_PIN_INDEX = 1;

  // Must disable interrupts, as interrupt handlers may be in flash, and we
  // are about to temporarily disable flash access!
  uint32_t flags = save_and_disable_interrupts();

  // Set chip select to Hi-Z
  hw_write_masked(&ioqspi_hw->io[CS_PIN_INDEX].ctrl,
                  GPIO_OVERRIDE_LOW << IO_QSPI_GPIO_QSPI_SS_CTRL_OEOVER_LSB,
                  IO_QSPI_GPIO_QSPI_SS_CTRL_OEOVER_BITS);

  // Note we can't call into any sleep functions in flash right now
  for (volatile int i = 0; i < 1000; ++i);

  // The HI GPIO registers in SIO can observe and control the 6 QSPI pins.
  // Note the button pulls the pin *low* when pressed.
  bool button_state = (sio_hw->gpio_hi_in & (1u << CS_PIN_INDEX));

  // Need to restore the state of chip select, else we are going to have a
  // bad time when we return to code in flash!
  hw_write_masked(&ioqspi_hw->io[CS_PIN_INDEX].ctrl,
                  GPIO_OVERRIDE_NORMAL << IO_QSPI_GPIO_QSPI_SS_CTRL_OEOVER_LSB,
                  IO_QSPI_GPIO_QSPI_SS_CTRL_OEOVER_BITS);

  restore_interrupts(flags);

  return button_state;
}
#endif

//------------- Segger RTT retarget -------------//
#if defined(LOGGER_RTT)
// Logging with RTT
// - If RTT Control Block is not found by 'Auto Detection` try to use 'Search Range` with '0x20000000 0x10000'
// - SWD speed is rather slow around 1000Khz
#include "pico/stdio/driver.h"
#include "SEGGER_RTT.h"

static void stdio_rtt_write (const char *buf, int length) {
  SEGGER_RTT_Write(0, buf, (unsigned) length);
}

static int stdio_rtt_read (char *buf, int len) {
  return (int) SEGGER_RTT_Read(0, buf, (unsigned) len);
}

static stdio_driver_t stdio_rtt = {
  .out_chars = stdio_rtt_write,
  .out_flush = NULL,
  .in_chars = stdio_rtt_read
};

void stdio_rtt_init(void) {
  stdio_set_driver_enabled(&stdio_rtt, true);
}
#endif

//--------------------------------------------------------------------+
//
//--------------------------------------------------------------------+

void board_init(void)
{
#if CFG_TUH_RPI_PIO_USB || CFG_TUD_RPI_PIO_USB
  // Set the system clock to a multiple of 120mhz for bitbanging USB with pico-usb
  set_sys_clock_khz(120000, true);

#ifdef PICO_DEFAULT_PIO_USB_VBUSEN_PIN
  gpio_init(PICO_DEFAULT_PIO_USB_VBUSEN_PIN);
  gpio_set_dir(PICO_DEFAULT_PIO_USB_VBUSEN_PIN, GPIO_OUT);
  gpio_put(PICO_DEFAULT_PIO_USB_VBUSEN_PIN, PICO_DEFAULT_PIO_USB_VBUSEN_STATE);
#endif

  // rp2040 use pico-pio-usb for host tuh_configure() can be used to passed pio configuration to the host stack
  // Note: tuh_configure() must be called before tuh_init()
  pio_usb_configuration_t pio_cfg = PIO_USB_DEFAULT_CONFIG;
  pio_cfg.pin_dp = PICO_DEFAULT_PIO_USB_DP_PIN;
  tuh_configure(BOARD_TUH_RHPORT, TUH_CFGID_RPI_PIO_USB_CONFIGURATION, &pio_cfg);
#endif

#ifdef LED_PIN
  bi_decl(bi_1pin_with_name(LED_PIN, "LED"));
  gpio_init(LED_PIN);
  gpio_set_dir(LED_PIN, GPIO_OUT);
#endif

  // Button
#ifndef BUTTON_BOOTSEL
#endif

#ifdef UART_DEV
  bi_decl(bi_2pins_with_func(UART_TX_PIN, UART_RX_PIN, GPIO_FUNC_UART));
  uart_inst = uart_get_instance(UART_DEV);
  stdio_uart_init_full(uart_inst, CFG_BOARD_UART_BAUDRATE, UART_TX_PIN, UART_RX_PIN);
#endif

#if defined(LOGGER_RTT)
  stdio_rtt_init();
#endif

#if CFG_TUD_ENABLED
  // TODO probably set up device mode?
#endif

#if CFG_TUH_ENABLED
  #if CFG_TUH_MAX3421
  max3421_init();
  #endif
#endif

#if !CFG_TUD_ENABLED && !CFG_TUH_ENABLED
  // board test exxample, reset usb controller
  reset_block(RESETS_RESET_USBCTRL_BITS);
  unreset_block_wait(RESETS_RESET_USBCTRL_BITS);
#endif
}

//--------------------------------------------------------------------+
// Board porting API
//--------------------------------------------------------------------+

void board_led_write(bool state) {
  (void) state;

#ifdef LED_PIN
  gpio_put(LED_PIN, state ? LED_STATE_ON : (1 - LED_STATE_ON));
#endif
}

uint32_t board_button_read(void) {
#ifdef BUTTON_BOOTSEL
  return BUTTON_STATE_ACTIVE == get_bootsel_button();
#else
  return 0;
#endif
}

size_t board_get_unique_id(uint8_t id[], size_t max_len) {
  pico_unique_board_id_t pico_id;
  pico_get_unique_board_id(&pico_id);

  size_t len = PICO_UNIQUE_BOARD_ID_SIZE_BYTES;
  if (len > max_len) len = max_len;

  memcpy(id, pico_id.id, len);
  return len;
}

int board_uart_read(uint8_t *buf, int len) {
#ifdef UART_DEV
  int count = 0;
  while ( (count < len) && uart_is_readable(uart_inst) ) {
    buf[count] = uart_getc(uart_inst);
    count++;
  }
  return count;
#else
  (void) buf; (void) len;
  return 0;
#endif
}

int board_uart_write(void const *buf, int len) {
#ifdef UART_DEV
  char const *bufch = (char const *) buf;
  for ( int i = 0; i < len; i++ ) {
    uart_putc(uart_inst, bufch[i]);
  }
  return len;
#else
  (void) buf; (void) len;
  return 0;
#endif
}

int board_getchar(void) {
  return getchar_timeout_us(0);
}

//--------------------------------------------------------------------+
// USB Interrupt Handler
// rp2040 implementation will install appropriate handler when initializing
// tinyusb. There is no need to forward IRQ from application
//--------------------------------------------------------------------+

//--------------------------------------------------------------------+
// API: SPI transfer with MAX3421E, must be implemented by application
//--------------------------------------------------------------------+
#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421

void max3421_int_handler(uint gpio, uint32_t event_mask) {
  if (!(gpio == MAX3421_INTR_PIN && event_mask & GPIO_IRQ_EDGE_FALL)) return;
  tuh_int_handler(BOARD_TUH_RHPORT, true);
}

static void max3421_init(void) {
  // CS pin
  gpio_init(MAX3421_CS_PIN);
  gpio_set_dir(MAX3421_CS_PIN, GPIO_OUT);
  gpio_put(MAX3421_CS_PIN, true);

  // Interrupt pin
  gpio_init(MAX3421_INTR_PIN);
  gpio_set_dir(MAX3421_INTR_PIN, GPIO_IN);
  gpio_pull_up(MAX3421_INTR_PIN);
  gpio_set_irq_enabled_with_callback(MAX3421_INTR_PIN, GPIO_IRQ_EDGE_FALL, true, max3421_int_handler);

  // SPI init
  spi_init(MAX3421_SPI, 4*1000000ul);
  gpio_set_function(MAX3421_SCK_PIN, GPIO_FUNC_SPI);
  gpio_set_function(MAX3421_MOSI_PIN, GPIO_FUNC_SPI);
  gpio_set_function(MAX3421_MISO_PIN, GPIO_FUNC_SPI);
  spi_set_format(MAX3421_SPI, 8, SPI_CPOL_0, SPI_CPHA_0, SPI_MSB_FIRST);
}

//// API to enable/disable MAX3421 INTR pin interrupt
void tuh_max3421_int_api(uint8_t rhport, bool enabled) {
  (void) rhport;
  irq_set_enabled(IO_IRQ_BANK0, enabled);
}

// API to control MAX3421 SPI CS
void tuh_max3421_spi_cs_api(uint8_t rhport, bool active) {
  (void) rhport;
  gpio_put(MAX3421_CS_PIN, !active);
}

// API to transfer data with MAX3421 SPI
// Either tx_buf or rx_buf can be NULL, which means transfer is write or read only
bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const* tx_buf, uint8_t* rx_buf, size_t xfer_bytes) {
  (void) rhport;

  if (tx_buf == NULL && rx_buf == NULL) {
    return false;
  }

  int ret;

  if (tx_buf == NULL) {
    ret = spi_read_blocking(MAX3421_SPI, 0, rx_buf, xfer_bytes);
  }else if (rx_buf == NULL) {
    ret = spi_write_blocking(MAX3421_SPI, tx_buf, xfer_bytes);
  }else {
    ret = spi_write_read_blocking(spi0, tx_buf, rx_buf, xfer_bytes);
  }

  return ret == (int) xfer_bytes;
}

#endif