274 lines
9.6 KiB
Markdown
274 lines
9.6 KiB
Markdown
|
|
PicoRV32 - A Size-Optimized RISC-V CPU
|
|
======================================
|
|
|
|
PicoRV32 is a CPU core that implements the [RISC-V RV32I Instruction Set](http://riscv.org/).
|
|
|
|
Tools (gcc, binutils, etc..) can be obtained via the [RISC-V Website](http://riscv.org/download.html#tab_tools).
|
|
|
|
PicoRV32 is free and open hardware licensed under the [ISC license](http://en.wikipedia.org/wiki/ISC_license)
|
|
(a license that is similar in terms to the MIT license or the 2-clause BSD license).
|
|
|
|
|
|
Features and Typical Applications:
|
|
----------------------------------
|
|
|
|
- Small (~1000 LUTs in a 7-Series Xilinx FGPA)
|
|
- High fMAX (>250 MHz on 7-Series Xilinx FGPAs)
|
|
- Selectable native memory interface or AXI4-Lite master
|
|
|
|
This CPU is meant to be used as auxiliary processor in FPGA designs and ASICs. Due
|
|
to its high fMAX it can be integrated in most existing designs without crossing
|
|
clock domains. When operated on a lower frequency, it will have a lot of timing
|
|
slack and thus can be added to a design without compromising timing closure.
|
|
|
|
For even smaller size it is possible disable support for registers `x16`..`x31` as
|
|
well as `RDCYCLE[H]`, `RDTIME[H]`, and `RDINSTRET[H]` instructions, turning the
|
|
processor into an RV32E core.
|
|
|
|
Furthermore it is possible to choose between a single-port and a dual-port
|
|
register file implementation. The former provides better performance while
|
|
the latter results in a smaller core.
|
|
|
|
*Note: In architectures that implement the register file in dedicated memory
|
|
resources, such as many FPGAs, disabling the 16 upper registers and/or
|
|
disabling the dual-port register file may not further reduce the core size.*
|
|
|
|
The core exists in two variations: `picorv32` and `picorv32_axi`. The former
|
|
provides a simple native memory interface, that is easy to use in simple
|
|
environments, and the latter provides an AXI-4 Lite Master interface that can
|
|
easily be integrated with existing systems that are already using the AXI
|
|
standard.
|
|
|
|
A separate core `picorv32_axi_adapter` is provided to bridge between the native
|
|
memory interface and AXI4. This core can be used to create custom cores that
|
|
include one or more PicoRV32 cores together with local RAM, ROM, and
|
|
memory-mapped peripherals, communicating with each other using the native
|
|
interface, and communicating with the outside world via AXI4.
|
|
|
|
|
|
Parameters:
|
|
-----------
|
|
|
|
The following Verilog module parameters can be used to configure the PicoRV32
|
|
core.
|
|
|
|
#### ENABLE_COUNTERS (default = 1)
|
|
|
|
This parameter enables support for the `RDCYCLE[H]`, `RDTIME[H]`, and
|
|
`RDINSTRET[H]` instructions. This instructions will cause a hardware
|
|
trap (like any other unsupported instruction) if `ENABLE_COUNTERS` is set to zero.
|
|
|
|
*Note: Strictly speaking the `RDCYCLE[H]`, `RDTIME[H]`, and `RDINSTRET[H]`
|
|
instructions are not optional for an RV32I core. But chances are they are not
|
|
going to be missed after the application code has been debugged and profiled.
|
|
This instructions are optional for an RV32E core.*
|
|
|
|
#### ENABLE_REGS_16_31 (default = 1)
|
|
|
|
This parameter enables support for registers the `x16`..`x31`. The RV32E ISA
|
|
excludes this registers. However, the RV32E ISA spec requires a hardware trap
|
|
for when code tries to access this registers. This is not implemented in PicoRV32.
|
|
|
|
#### ENABLE_REGS_DUALPORT (default = 1)
|
|
|
|
The register file can be implemented with two or one read ports. A dual ported
|
|
register file improves performance a bit, but can also increase the size of
|
|
the core.
|
|
|
|
#### LATCHED_MEM_RDATA (default = 0)
|
|
|
|
Set this to 1 if the `mem_rdata` is kept stable by the external circuit after a
|
|
transaction. In the default configuration the PicoRV32 core only expects the
|
|
`mem_rdata` input to be valid in the cycle with `mem_valid && mem_ready` and
|
|
latches the value internally.
|
|
|
|
#### ENABLE_IRQ (default = 0)
|
|
|
|
Set this to 1 to enable IRQs.
|
|
|
|
#### MASKED_IRQ (default = 32'h 0000_0000)
|
|
|
|
A 1 bit in this bitmask corresponds to a permanently disabled IRQ.
|
|
|
|
#### PROGADDR_RESET (default = 32'h 0000_0000)
|
|
|
|
The start address of the program.
|
|
|
|
#### PROGADDR_IRQ (default = 32'h 0000_0010)
|
|
|
|
The start address of the interrupt handler.
|
|
|
|
|
|
Performance:
|
|
------------
|
|
|
|
*A short reminder: This core is optimized for size, not performance.*
|
|
|
|
Unless stated otherwise, the following numbers apply to a PicoRV32 with
|
|
ENABLE_REGS_DUALPORT active and connected to a memory that can accomodate
|
|
requests within one clock cycle.
|
|
|
|
The average Cycles per Instruction (CPI) is 4 to 5, depending on the mix of
|
|
instructions in the code. The CPI numbers for the individual instructions
|
|
can be found in the table below. The column "CPI (SP)" contains the
|
|
CPI numbers for a core built without ENABLE_REGS_DUALPORT.
|
|
|
|
| Instruction | CPI | CPI (SP) |
|
|
| ---------------------| ----:| --------:|
|
|
| direct jump (jal) | 3 | 3 |
|
|
| ALU reg + immediate | 3 | 3 |
|
|
| ALU reg + reg | 3 | 4 |
|
|
| branch (not taken) | 3 | 4 |
|
|
| memory load | 5 | 5 |
|
|
| memory store | 5 | 6 |
|
|
| branch (taken) | 5 | 6 |
|
|
| indirect jump (jalr) | 6 | 6 |
|
|
| shift operations | 4-14 | 4-15 |
|
|
|
|
Dhrystone benchmark results: 0.309 DMIPS/MHz (544 Dhrystones/Second/MHz)
|
|
|
|
For the Dhrystone benchmark the average CPI is 4.167.
|
|
|
|
|
|
Custom Instructions for IRQ Handling
|
|
------------------------------------
|
|
|
|
The following custom instructions are supported when IRQs are enabled.
|
|
|
|
The PicoRV32 core has a built-in interrupt controller with 32 interrupts. An
|
|
interrupt can be triggered by asserting the corresponding bit in the `irq`
|
|
input of the core.
|
|
|
|
When the interrupt handler is started, the `eoi` End Of Interrupt (EOI) signals
|
|
for the handled interrupts goes high. The `eoi` signal goes low again when the
|
|
interrupt handler returns.
|
|
|
|
The IRQs 0-2 can be triggered internally and have the following meaning:
|
|
|
|
| IRQ | Interrupt Source |
|
|
| ---:| -----------------------------------|
|
|
| 0 | Timer Interrupt |
|
|
| 1 | SBREAK or Illegal Instruction |
|
|
| 2 | BUS Error (Unalign Memory Access) |
|
|
|
|
The core has 4 additional 32-bit registers `q0 .. q3` that are used for IRQ
|
|
handling. When an IRQ triggers, the register `q0` contains the return address
|
|
and `q1` contains a bitmask of all active IRQs. I.e. one call to the interrupt
|
|
handler might need to service one than more IRQ when more than one bit is set
|
|
in `q1`.
|
|
|
|
Registers `q2` and `q3` are uninitialized and can be used as temporary storage
|
|
when saving/restoring register values in the IRQ handler.
|
|
|
|
#### getq rd, qs
|
|
|
|
This instruction copies the value from a q-register to a general-purpose
|
|
register. The Instruction is encoded under the `custom0` opcode:
|
|
|
|
0000000 00000 000XX 000 XXXXX 0001011
|
|
f7 f5 qs f3 rd opcode
|
|
|
|
Example assembler code using the `custom0` mnemonic:
|
|
|
|
| Instruction | Assember Code |
|
|
| ------------------| --------------------|
|
|
| getq x5, q2 | custom0 5, 2, 0, 0 |
|
|
| getq x3, q0 | custom0 3, 0, 0, 0 |
|
|
| getq x1, q3 | custom0 1, 3, 0, 0 |
|
|
|
|
#### setq qd, rs
|
|
|
|
This instruction copies the value from a general-purpose register to a
|
|
q-register. The Instruction is encoded under the `custom0` opcode:
|
|
|
|
0000001 00000 XXXXX 000 000XX 0001011
|
|
f7 f5 rs f3 qd opcode
|
|
|
|
Example assembler code using the `custom0` mnemonic:
|
|
|
|
| Instruction | Assember Code |
|
|
| ------------------| --------------------|
|
|
| setq q2, x5 | custom0 2, 5, 0, 1 |
|
|
| setq q0, x3 | custom0 0, 3, 0, 1 |
|
|
| setq q3, x1 | custom0 3, 1, 0, 1 |
|
|
|
|
#### retirq
|
|
|
|
Return from interrupt. This instruction copies the value from `q0`
|
|
to the program counter and re-enables interrupts. The Instruction is
|
|
encoded under the `custom0` opcode:
|
|
|
|
0000010 00000 00000 000 00000 0001011
|
|
f7 f5 rs f3 rd opcode
|
|
|
|
Example assembler code using the `custom0` mnemonic:
|
|
|
|
| Instruction | Assember Code |
|
|
| ------------------| --------------------|
|
|
| retirq | custom0 0, 0, 0, 2 |
|
|
|
|
#### maskirq
|
|
|
|
The "IRQ Mask" register contains a birtmask of masked (disabled) interrupts.
|
|
This opcodes writes a new value to the irq mask register and reads the old
|
|
value.
|
|
|
|
Enable/disable interrupt sources. The Instruction is encoded under the
|
|
`custom0` opcode:
|
|
|
|
0000011 00000 XXXXX 000 XXXXX 0001011
|
|
f7 f5 rs f3 rd opcode
|
|
|
|
Example assembler code using the `custom0` mnemonic:
|
|
|
|
| Instruction | Assember Code |
|
|
| ------------------| --------------------|
|
|
| maskirq x1, x2 | custom0 1, 2, 0, 3 |
|
|
|
|
The processor starts with all interrupts disabled.
|
|
|
|
An illegal instruction or bus error while the illegal instruction or bus error
|
|
interrupt is disabled will cause the processor to halt.
|
|
|
|
#### waitirq (unimplemented)
|
|
|
|
Pause execution until an interrupt triggers. The Instruction is encoded under the
|
|
`custom0` opcode:
|
|
|
|
0000100 00000 00000 000 00000 0001011
|
|
f7 f5 rs f3 rd opcode
|
|
|
|
Example assembler code using the `custom0` mnemonic:
|
|
|
|
| Instruction | Assember Code |
|
|
| ------------------| --------------------|
|
|
| waitirq | custom0 0, 0, 0, 4 |
|
|
|
|
#### timer
|
|
|
|
Reset the timer counter to a new value. The counter counts down clock cycles and
|
|
triggers the timer interrupt when transitioning from 1 to 0. Setting the
|
|
counter to zero disables the timer.
|
|
|
|
0000101 00000 XXXXX 000 00000 0001011
|
|
f7 f5 rs f3 rd opcode
|
|
|
|
Example assembler code using the `custom0` mnemonic:
|
|
|
|
| Instruction | Assember Code |
|
|
| ------------------| --------------------|
|
|
| timer x2 | custom0 0, 2, 0, 5 |
|
|
|
|
|
|
Todos:
|
|
------
|
|
|
|
- Optional FENCE support
|
|
- Optional Co-Processor Interface
|
|
- Optional write-through cache
|
|
- Optional support for compressed ISA
|
|
- Improved documentation and examples
|
|
- Code cleanups and refactoring of main FSM
|
|
|